View LV8800V_4222264.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Ordering number : ENA0845A
LV8800V
Overview
Bi-CMOS IC
For Notebook PC
Fan Motor Driver
The LV8800V is a motor driver for notebook PC fans.
Feature
* Direct PWM sensorless motor driver
Specifications
Absolute Maximum Ratings at Ta = 25C
Parameter Power supply voltage Predrive voltage (gate voltage) Output pin current PWM input pin withstand voltage FG output pin withstand voltage FG output current Power dissipation 1 Power dissipation 2 Operating temperature Storage temperature Symbol VCC max VG max IOUT max VPWM max VFG max IFG max Pd max1 Pd max2 Topr Tstg Independent IC Mounted on specified board *1 *2 Conditions Ratings 6.5 10 0.7 VCC 6.0 5.0 0.3 0.8 -30 to +95 -55 to +150 Unit V V A V V mA W W C C
*1 : When mounted on 76.1mmx114.3mmx1.6mm glass epoxy board *2 : Tj max = 150C. Use the IC in the range where the temperature of the chip does not exceed Tj = 150C during operation.
Recommended Operating Conditions at Ta = 25C
Parameter Power supply voltage Symbol VCC Conditions Ratings 2.2 to 6.0 Unit V
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment.
82907 MS 20070726-S00002 / 62007 MS PC 20070529-S00004 No.A0845-1/7
LV8800V
Electrical Characteristics Ta = 25C, VCC = 5V, unless specifically noted
Parameter Power supply current 1 Power supply current 2 Charge pump output Output voltage Output block Source Sink Source + sink Startup oscillation pin OSC pin charge current OSC pin discharge current PWM input pin PWM pin high-level input voltage PWM pin low-level input voltage PWM pin input current PWM input frequency FG output pin FG output pin low-level voltage Current limiter circuit Limiter voltage Constraint protection circuit Constraint protection detection time Constraint protection release time Thermal protection circuit Thermal protection circuit operating temperature Temperature hysteresis width TSD Design target * 30 C TSD Design target * 150 180 C RDT1 RDT2 0.5 5 1.0 s s VRf RF = 0.5 0.225 0.25 0.275 V VFG When IO = 0.5mA 0.1 0.2 V VPWMH VPWML IPWM fPWM PWM pin = 0V 20 25 VCCx0.8 0 VCC VCCx0.2 -50 50 V V A kHz IOSC1 IOSC2 -2.5 2.5 A A Ron (H) Ron (L) Ron (H+L) IO = 0.5A, VG = 9.5V IO = 0.5A, VCC = 5.0V IO = 0.5A, VCC = 5V, VG = 9.5V 0.6 0.6 1.2 1.0 1.0 2 VG 9.8 V Symbol ICC1 ICC2 Conditions min PWM pin = VCC PWM pin = 0V Ratings typ 1.8 20 max 2.5 50 mA A Unit
* : Design target value and no measurement is made. The thermal protection circuit is incorporated to protect the IC from burnout or thermal destruction. Since it operates outside the IC's guaranteed operating range, the customer's thermal design should be performed so that the thermal protection circuit will not be activated when the fan is running under normal operating conditions.
Package Dimensions
unit : mm (typ) 3178B
1.0
Pd max - Ta
Specified circuit board : 76.1x114.3x1.6mm3 glass epoxy board
5.2 16 9
Allowable power dissipation, Pd max - W
0.8
0.6
4.4
6.4
0.5
0.4 0.35
1 0.65 (0.33)
8 0.15 0.22
1.5max
0.2
0 - 30 - 20
0
20 25
40
60
80
95 100
SANYO : SSOP16(225mil)
0.1 (1.3)
Ambient temperature, Ta - C
No.A0845-2/7
LV8800V
Pin Assignment
VO UO VCC COM COMIN FIL OSC SGND
1 2 3
16 WO 15 RF 14 CPC
LV8800V
4 5 6 7 8
13 CP 12 VG 11 PWM 10 FG 9 F/R
Top view
Block Diagram
VG VCC
WO VO UO TSD VREF
RF SGND CURRENT LIMITTER COM SELECTOR PRE DRIVE LOCK PROTECT LOGIC
COMIN FIL OSC VG CP CPC CHARGE PUMP MOSC 1/N OSC SENSORLESS LOGIC FG PWM FR
No.A0845-3/7
LV8800V
Pin Functions
Pin No. 3 Pin name VCC Function Power supply for the IC and motor. A capacitor must be connected between this pin and ground. 2 1 16 15 UO VO WO RF Output current detection. The drive current is detected by connecting a resistor between this pin and ground. Output pins. Connect the motor coil. Equivalent circuit
3
2 50k
1 50k
16 50k 15
4 5
COM COMIN
Motor middle point connection. Motor position detection comparator filter pin. A capacitor must be connected between this pin and the FIL pin (pin 6).
VG
50k 50k 50k
UO VO WO
6
FIL
Motor position detection comparator filter pin. A capacitor must be connected between this pin and the COMIN pin (pin 5).
4
1k
6k
6k
1k
5
6
7
OSC
Motor startup frequency setting. A capacitor must be connected between this pin and ground. The startup frequency is adjusted by controlling the charge/discharge current (2.5A) and the capacitance of the capacitor.
VCC
VCC 500
7
500
8 9
SGND F/R
Ground for IC. Motor rotation direction switching. A high-level input causes current to flow into the motor in the order of U, V, and W and a low-level input in the order of U, W, and V. Changing the order of current application turns the motor in the opposite direction.
VCC
Reverse signal
9 100k Forward signal
Forward/reverse switching signal
10
FG
FG pulse output. This pin outputs a Hall sensor system equivalent pulse signal.
10
11
PWM
PWM signal input. A high-level input turns on the output transistors. A low-level input turns off the output transistors and motor stops. The motor speed is set by controlling the duty cycle of the input PWM signal. The motor runs at full speed when this pin is held open.
VCC
300k 11
15k
Continued on next page.
No.A0845-4/7
LV8800V
Continued from preceding page. Pin No. 12 Pin name VG Function Charge pump step-up output. A capacitor must be connected between this pin and ground. Equivalent circuit
13 VCC
14
12
13
CP
Charge pump step-up pulse output pin. A capacitor must be connected between this pin and the CPC pin (pin 14).
14
CPC
Charge pump step-up pin. A capacitor must be connected between this pin and the CP pin (pin 13).
LV8800V Functional Description and Notes on External Components Read the following notes before designing driver circuits using the LV8800V to design a system with fully satisfactory characteristics. 1. Output drive circuit and speed control methods The LV8800V adopts the synchronous commutation PWM drive method to minimize power loss in the output circuits. Low on-resistance DMOS devices (total high and low side on-resistance of output block : 1.2, typical) are used as the output transistors. The speed control of the driver is performed with an externally input PWM signal. PWM controls the speed by performing switching in accordance with the duty cycle that is input to the PWM pin (11-pin). The output transistor is on when a high-level voltage is input to the PWM pin, and off when a low-level voltage is input. When the motor is used with the PWM pin open, the built-in resistor causes the PWM pin to change to high-level voltage and the motor speed rises to full speed. When the PWM pin is fixed at low-level voltage, the motor decelerates, and after the motor stops it enters "Power Saving Mode. 2. Soft Switching Circuit This IC adopts variable duty soft switching to minimize the motor drive noise. 3. Current limiter circuit The current limiter circuit limits the output current peak value to a level determined by the equation I = VRF/RF (VRF = 0.25V typical). The current limiter circuit detects the peak current of the output transistors at the RF pin (pin 15) and turns off the transistor of the PWM phase. 4. OSC circuit The OSC pin (pin 7) is an oscillation pin provided for sensorless motor startup commutation. When a capacitor is connected between the OSC pin and ground, the OSC pin starts self-oscillation, and this becomes the startup frequency. The oscillator frequency can be adjusted by changing the value of the external capacitor (i.e. reducing the value of the capacitor increases the startup frequency). It is necessary to select a value of the capacitor that provides the optimal startup characteristics. 5. Position Detector Comparator Circuit for Rotor The position detection comparator circuit for the rotor is a comparator for detecting rotor positional information with the back EMF signal generated when the motor rotates. The IC determines the timing at which the output block applies current to the motor based on the position information obtained here. Insert a capacitor (between 1,000 and 10,000pF) between the COMIN pin (pin 5) and FIL (pin 6) to prevent any motor startup missoperation that is caused by the comparator input noise. 6. FG Output Circuit The FG pin (pin 10) is the FG output pin. It provides a pulse signal equivalent to that provided by systems that use a Hall-effect sensor.
No.A0845-5/7
LV8800V
Since the FG pin has an open drain output structure, it must be used with a pull-up resistor. Connect a pull-up resistor on the side of the power supply where the FG signal is input. A pull-up resistor with a resistance of about 10k is recommended.
No.A0845-6/7
LV8800V
7. Charge Pump Circuit The LV8800V n-channel DMOS output structure allows it to provide a charge pump based voltage step-up circuit. A voltage 2 times the VCC voltage can be acquired by inserting capacitors (recommended value : 0.1F or larger) between the CP pin (pin 13) and CPC pin (pin 14). Note that this circuit is designed so that the stepped-up voltage (VG) is clamped at about 9.5VDC. A larger capacitor must be used between the VG pin (pin 12) and ground if the ripple on the stepped-up voltage (VG) results in VG exceeding 10V(VG max). Observe the following points if the VG voltage is supplied from external circuits. (1) The VG voltage supplied from the external circuits must not exceed the absolute maximum rating VG max. (2) The capacitors between the CP pin (pin 13) and CPC pin (pin 14) are not required. (3) Observe the correct sequence when turning the power supply on. Apply the VG voltage after first turning the VCC voltage on, and cancel the VG voltage application before turning the VCC off. (4) There is an IC-internal diode between the VCC and VG pins. Therefore, supply voltages such that VCC > VG must never be applied to this IC. 8. Notes on PCB Pattern Design The LV8800V is a system driver IC implemented using the Bi-CMOS process; the IC chip includes bipolar circuits, MOS logic circuits, and MOS drive circuits. As a result, extreme care is required with respect to the pattern layout when designing application circuits. (1) Ground and VCC wiring layout Insert a capacitor (recommended value : 1F or larger) as near as possible to the pin between the power pin (pin 3) and ground pin (pin 8). (2) Positioning the external components The external components that are connected to ground must be connected with lines that are as short as possible. External components connected between IC pins must be placed as near to the pins as possible.
Application Circuit Example
1 VO
WO 16
2 UO
RF 15 0.5
VCC 1F
3 VCC
CPC 14 0.1F
4 COM
CP 13
0.1F 5 COMIN 1000pF 6 FIL PWM 11 PWM VG 12
7 OSC 2200pF 8 SGND
FG 10
PWM Control Signal f = 20k to 50kHz
F/R
9
No.A0845-7/7
LV8800V
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above.
This catalog provides information as of August, 2007. Specifications and information herein are subject to change without notice. PS No.A0845-8/8

▲Up To Search▲

Price & Availability of LV8800V

	To Download LV8800V Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .